Categories
Quick Add To Cart

Plates

Each individual MEA produces less than 1 V under typical operating conditions, but most applications require higher voltages. Therefore, multiple MEAs are usually connected in series by stacking them on top of each other to provide a usable output voltage. Each cell in the stack is sandwiched between two bipolar plates to separate it from neighboring cells. These plates, which may be made of metal, carbon, or composites, provide electrical conduction between cells, as well as providing physical strength to the stack. The surfaces of the plates typically contain a “flow field,” which is a set of channels machined or stamped into the plate to allow gases to flow over the MEA. Additional channels inside each plate may be used to circulate a liquid coolant.

The picture to the right shows four different types of serpentine flow channels in graphite plates: (A) a single serpentine channel; (B) double serpentine flow channels; (C) four serpentine flow channels; and (D) a symmetric arrangement of four serpentine flow channels.

Display: List / Grid
Show:
Sort By:
Flex-Stak Closed Bipolar Graphite Plate - 10 cm²
These closed bipolar graphite plates can be used as replacements plates for the Flex-Stak Electroc..
$54.00

Flex-Stak Closed Monopolar Graphite Plate - 10 cm²
These closed monopolar plates can be used for the Flex-Stak Series, or you can use them as the bas..
$54.00

Flex-Stak Open Bipolar Graphite Plate - 10 cm²
10 cm2 Open Bipolar Graphite plate suitable for small Hydrogen / Air Fuel Cells and Methanol ..
$54.00

Flex-Stak Open Monopolar Graphite Plate - 10 cm²
These open monopolar plates can be used for the Flex-Stak Series, or you can use them as the basis..
$54.00

Fuel Cell Grade Graphite Plate, 4" x 4" x 5mm
Fuel Cell Grade Graphite Plates can be machined on both sides to be used as bi-polar plates.  ..
$66.00

Fully Resin Impregnated Graphite Plates
Fuel Cell Grade Graphite Plates can be machined on both sides to be used as bi-polar plates. Thes..
From $161.00

Garolite Sheet - 6" x 6"
This Garolite sheet can be used to make fuel cell end plates. This Garolite grade is the flame-re..
From $31.00

(2) Hot-Press Aluminum Plates
Set of two Aluminum, alloy 6061 plates ideal for hot pressing Membrane Electrode Assemblies (MEA)..
From $92.00
Based on 1 reviews.

Garolite Sheet - 12" x 12"
This Garolite sheet can be used to make fuel cell end plates. This Garolite grade is the flame-re..
From $59.00

Isomolded Graphite Plate - 4" x 4"
These Isomolded Graphite Plates can be machined on both sides.  Isomolded plates are made out..
From $42.00
Based on 1 reviews.

Isomolded Graphite Plate - 4" x 6"
These Isomolded Graphite Plates can be machined on both sides.  Isomolded plates are made out..
From $70.00

Isomolded Graphite Plate - 6" x 6"
These Isomolded Graphite Plates can be machined on both sides.  Isomolded plates are made out..
From $81.00

Isomolded Graphite Plate - 8" x 8"
These Isomolded Graphite Plates can be machined on both sides.  Isomolded plates are made out..
From $147.00
Based on 1 reviews.

Isomolded Graphite Plate - 12" x 12"
These Isomolded Graphite Plates can be machined on both sides.  Isomolded plates are made out..
From $246.00

PEMFC Graphite Flow Field Plate, Serpentine - 5 cm2
5 cm2 graphite plate with serpentine flow field that is suitable for H2/Air (hydrogen / air),..
From $450.00