- Fuel Cell Cars
- Fuel Cell Stacks
- Fuel Cell Testing
- Fuel Cell Components
- Hydrogen Equipment
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- STEM Education
H-TEC's Tutorial Basic, T126 is a Solar Hydrogen Experimentation System consisting of single components, such as solar module, PEM electrolyser, hydrogen, and oxygen storage tanks, PEM fuel cell and fan (for electric load); each with magnetic base for modular arrangement on a base plate and textbook. The included H-TEC Education fuel cell textbook contains information about the technology and instructions for a variety of experiments.
The Tutorial Basic reflects the simple elegance of the hydrogen cycle by reflecting a self-contained hydrogen system that is perfect for introducing the technology behind the solar hydrogen cycle, or for small demonstrations.
✔ Compact system on one base-plate
✔ Clear, self-explanatory set-up
✔ Sturdy construction
✔ Short setup time
Recommended Grades: 5 - 12
✔ Producing and storing hydrogen and oxygen
✔ Determining characteristic curve of solar panel
✔ Operating the fuel cell with hydrogen and oxygen 2:1
✔ Determining characteristic curve of electrolyser
✔ Determining electrolyser efficiency
✔ Hydrogen / oxygen or hydrogen / air operation
✔ Determining characteristic curves of fuel cell
✔ Determining fuel cell efficiency
✔ Determining decomposition voltage of water
✔ Storing electrical energy from wind by using hydrogen technology
✔ Demonstrating a complete renewable hydrogen energy system
For the blue experiments listed above you will also need the Measurement Set (product code: 1071077).
For the green experiments listed above you will also need the Wind Generator (product code: 1071066).
PEM Electrolyzer Cell 5
The PEM Electrolyzer separates water into hydrogen and oxygen. It is operated with distilled water and requires no caustic solutions or acids.
• Electrode Area: 4 cm²
• Power: 1.16 W
• Permissible Voltage: 0 - 2 V DC
• Permissible Current: 0 - 2 A DC
• Hydrogen Production: 5 cm3/min
• Oxygen Production: 2.5 cm3/min
x2 Storage 30
The graduated hydrogen, oxygen, and water storage cylinders visualize the classic hydrogen separation experiment, as in the Hoffmann apparatus.
• Gas / Water Capacity Per Tank: 30 cm3
PEM Fuel Cell H2/O2/Air
The PEM Fuel Cell generates electrical energy from hydrogen and oxygen or hydrogen and air. It is based on PEM technology, which is the most widespread technology used in the development of fuel cell applications, e.g. for motor vehicles or stationary power supply systems.
• Power in H2/O2 Mode: 500mW
• Power in H2/Air Mode: 150mW
• Dimensions (H x W x D): 2" x 1.6" x 2" (50 x 40 x 50 mm)
• Weight: 1.8 oz (52 g)
Provides electricity to run the model’s PEM Electrolyser
• Cell Area: 90 cm²
• Open Circuit Voltage: 2 V
• Current: 350 mA
• Power (MPP): 500 mW
• Power: 10 mW
• Dimensions (H x W x D): 4.8" x 1.4" x 2.1" (135 x 40 x 60 mm)
• Weight: 2.3 oz (66 g)
• Plug Size: 2 mm
• Length: 39 inches (100 cm)
The textbook contains information about the technology and instructions for a variety of experiments.
Metal Base Plate
A black metal plate that allows you to connect the magnetic bases of each item on to it.
Entire Junior Set
• Dimensions (H x W x D): 5.5" x 17.7" x 15" (140 x 450 x 380 mm)
• Weight: 2.8 pounds (1.25 kg)
1) The fuel cell only produces low power.
Cause: The cell has been stored for a very long time or is too dry. A cell with a dry membrane will lose power.
Solution: Continue operating the cell. The cell will moisten itself during operation and gradually return to full power.
2) The electric load connected to the cell does not work, despite hydrogen being present.
Cause: Water has gotten into the fuel cell (e.g. via the storage tank). Drops of water in the fuel cell can block the gas feed and lead to a rapid loss of power.
Solution: Dry the cell by opening the connectors and blowing through the cell.
3) No hydrogen is produced by the electrolyser when the solar cell is connected.
Cause: The light intensity is insufficient.
Solution: Check the power specifi cations designed for the light source. You need suffi cient sunlight or halogen lamps with focused light such as the Sun Simulator Light. Energy-saving lamps, fluorescent tubes, etc. are not suitable for the operation of solar modules.
4) The electrolyser does not work despite being set up correctly.
Cause: You have not used distilled water. The cell is permanently damaged
Write a review
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: