Categories

Materials Used for High-Temperature Fuel Cells

In a previous blog post, we described bipolar plates and the associated materials for low-temperature fuel cells. The materials previously described are selected for fuel cell stacks at or slightly above room-temperature -- which means that the materials are chemically compatible with the stack between 0 – 140 °C. The fuel cells that operate at higher temperatures require different materials. Fuel cell stacks that operate at high temperatures are SOFCs, MCFCs, and PAFCs. We will describe the materials typically used for these fuel cells types in this blog post.

Solid Oxide Fuel Cells (SOFCs)

The materials used in SOFCs must be physically stable and resist corrosion from the electrolyte at high temperatures. There are two categories of materials used for SOFC plates: high-temperature perovskite materials (900 to 1000 °C) and metallic alloys for lower temperature operation (600 to 900 °C).  The high-temperature perovskite materials used in SOFCs are doped lanthanum and yttrium chromites (dopants typically include Mg, Sr, Ca, Ca/Co). These materials have good electronic conductivity -- which increases with temperature. The type of dopant alters the material properties and determines the compatibility with the fuel cell layers.

Ceramic interconnects are chemically and physically stable in SOFCs for extended periods of time, but because the interconnects are made of ceramic, they do not have good flexibility for sealing the cell. To remedy this issue, conductive pastes or a contact felt is sometimes used. These help with the flexibility and sealing, but of course, the life of these components are not as good as the ceramic interconnect.

When thin-electrolyte anode-supported SOFCs (Figure 1) were developed within the last decade, this enabled the SOFC to be operated at lower temperatures (650 to 800 °C), which allowed the use of some metallic components in the cell. Even at these “lowered” temperatures, it is difficult to find reliable metals that can be used as interconnects. Metals that will be used as SOFC interconnects at these temperatures must have the following characteristics:

• Able to maintain uniform temperature across the plate without deformation
• Have sufficient creep strength
• Tolerate a corrosive environment
• Maintain a high conductivity

   

Figure 1 (Left to Right): Electrolyte Supported Button Cell and Electrolyte Supported Planar Cell

Many high-chrome interconnects have been developed, such as Cr5Fe1Y2O3, which operates around 900 °C. The chrome is problematic because it can poison the electrode. If the operating temperatures were reduced, ferritic steels could be used, which would reduce the material and processing costs. The following materials are commonly used as end-plate materials in fuel cells:

• Lanthanum chromite
• Cr5Fe1Y2O3
• Avesta 600 (Fe-28/Cr-4/Ni-2/Mo)
• Inconel 601 (NiCr + Al)
• SS 310
• SS 316L
• SS 310S

Metals used in high-temperature fuel cells often have to be coated to be non-corrosive, which means that the coating needs to have similar properties as the ideal interconnect. The most commonly used coating is a stable oxide (chromia) which leads to evaporation and electrode poisoning.

Two coatings that minimize evaporation and insure good contact resistance are strontium-doped lanthanum cobaltite or manganite (Figure 2). These coatings perform well in the intermediate temperature range, but better coatings and interconnect materials still need to be developed in the future.

   

Figure 2 (Left to Right): Lanthanum Strontium Cobaltite Ink and Lanthanum Strontium Manganite Ink

Molten Carbonate Fuel Cells (MCFCs)

Bipolar plates for MCFCs include a separator, current collectors, and the wet seal. The materials used for MCFC bipolar plates are alloys such as Incoloy 825, 310S or 316L stainless steel that are coated on one side with a Ni layer. The plates are typically 15 mm thick, and the nickel-coated side provides a conductive surface coating with low contact resistance. A thin aluminum coating can form a protective LiAlO2 after reaction of Al with Li2CO3. This coating is not useful for areas that need to be conductive since it is an insulating protective layer. Materials that are commonly used to promote conductivity and have corrosion resistance are 316 stainless steel, and Ni plated stainless steels. Type 310 and 446 stainless steels have better corrosion resistance than Type 316 in corrosion tests.

The separator and current collector is a Ni-coated 310S/316L, and the wet seal is formed by aluminization of the metal. A low oxygen partial pressure on the anode side of the bipolar plate prevents oxidation. Single alloy bipolar current collector plates need to be developed that work on both the cathode and anode sides of the fuel cell. The primary construction materials are stainless steels (austenitic stainless steels).  Nickel-based alloys also resist corrosion well. Certain nickel-based coatings can protect the anode side. Electroless nickel coatings are thick and uniform, but expensive, and contain large amounts of impurities. Electrolytic nickel coatings are not sufficiently dense or uniform in thickness.

Phosphoric Acid Fuel Cells (PAFCs)

PAFCs use many of the same materials as in low-temperature cells. Pure graphite bipolar plates are corrosion-resistant for a projected life of 40,000 hours in PAFCs, but like in other low-temperature fuel cells – are costly and expensive to manufacture. Another commonly used design is a multi-component bipolar plate, which has a thin, impervious plate that separates the reactant gases in adjacent cells, and a separate porous plate with ribbed channels that is used for gas flow. The impervious plate is subdivided into two parts, and each joins one of the porous plates. Metals that can withstand higher temperatures are also used as materials in PAFC stacks.

Conclusion

High-temperature fuel cells often use different materials than fuel cells that operate at room temperature (or below 140 °C). Some of the materials used for SOFCs are perovskite and doped lanthanum and yttrium chromites. Materials for MCFCs include Incoloy 825, 310S or 316L stainless steel and are often coated with Nickel. PAFCs use some of the materials from lower-temperature fuel cells and other materials that are used by SOFCs and MCFCs.

Dr. Colleen Spiegel Posted by Dr. Colleen Spiegel

Dr. Colleen Spiegel is a mathematical modeling and technical writing consultant (President of SEMSCIO) and Professor holding a Ph.D. and an MSc degree in Engineering. She has seventeen years of experience in engineering, statistics, data science, research & technical writing work for many companies as a consultant, employee, and independent business owner. She is the author of ‘Designing and Building Fuel Cells’ (McGraw-Hill, 2007) and ‘PEM Fuel Cell Modeling and Simulation Using MATLAB’ (Elsevier Science, 2008). She previously owned Clean Fuel Cell Energy, LLC, which was a fuel cell organization that served scientists, engineers, and professors world-wide.

Products related to this article

Related Articles

Gas Diffusion Layer for Low-Temperature Fuel Cells

The gas diffusion layer is sandwiched between the catalyst layer and the bipolar plates as shown in Figure 1. The gas diffusion layer (GDL) provides electrical contact between electrodes and the bipolar plates and distribute reactants to the electrodes. The GDL also allows the water that is generated as a result of the chemical reaction to move between the electrodes and the ...

Low-Temperature Fuel Cell Membrane Electrode Assembly Processing Techniques

The fuel cell stack consists of many layers, including: The Membrane Electrode Assembly (MEA), Gaskets, Flow field plates, and End plates.  There are two standard methods of assembling the membrane electrode assembly (MEA) in low-temperature fuel cells. The catalyst layer can be applied in one or two steps. For the first method, there are five common ways to prepare and apply the catalyst for the GDL/catalyst assembly:

The Fuel Cell Electrolyte Layer for Low-Temperature Fuel Cells

The electrolyte layer is essential for a fuel cell to work properly. In low-temperature fuel cells, when the fuel in the fuel cell travels to the catalyst layer, the fuel molecule gets broken into protons (H+) and electrons. The electrons travel to the external circuit to power the load, and the hydrogen proton (ions) travel through the electrolyte until it reaches...

Catalysts for Low Temperature Fuel Cells

The fuel cell electrode is a thin, catalyst layer where electrochemical reactions take place. The electrodes are usually made of a porous mixture of carbon-supported platinum and ionomer. To catalyze reactions, catalyst particles have contact to both protonic and electronic conductors. There also must be passages for...

Gas Diffusion Layer: Characteristics and Modeling

The gas diffusion layer (GDL) in a fuel cell can consist of a single layer or a double layer (gas diffusion layer and a microporous layer). The GDL is an essential part of the fuel cell because it causes the gases to spread out to maximize the contact surface area with the catalyst...

2 Comments To "Materials Used for High-Temperature Fuel Cells"

Marc DeLisle On 10.26.2018
What is the purpose of the "Graphene", and required amounts? Reply to this comment
Frederick A. On 10.29.2018
Graphene is a mono-layer carbon structure that is theoretically conducts both thermal and electrical energies very efficiently. This is interesting material but it has not made it into mainstream.

Write a comment

Your Name:


Enter the code in the box below:

Your Comment:
Note: HTML is not translated!