- Fuel Cell Cars
- Fuel Cell Stacks
Fuel Cell Testing
- - Fixed Testing Systems
- - Liquid and Gas Delivery Systems
- - Fuel Cell Testing Hardware
- - Modular Testing Systems
- - Vacuum Tables and Temperature Controllers
- - Electronic Measurement and Control
- - Stack Humidification Systems
- - Ion Exchange Filters
- - Fuel Cell Testing Components
- - Portable Generators
- - Electrochemical Experiments
- Fuel Cell Components
- Hydrogen Equipment
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- STEM Education
Build your own PEM hydrogen fuel cell from the endplates up! The Flex-Stak fuel cell kit gives you all the materials you need to make your very own fuel cell from scratch. It allows the user to increase their basic fundamental understanding of the fuel cell and all of the components required.
The Flex-Stak Kit comes in a 1-cell, 5-cell, 10-cell, 15-cell, or 20-cell stack configuration depending on your hydrogen power requirements. This open-air cathode stack can be fitted with various sizes of graphite plates, membrane electrode assemblies (MEA) and low temperature PEM membranes to run on Hydrogen and Air or Hydrogen and Oxygen. The ease of use makes it simple to scale the Flex-Stak to different power levels and integrate equipment such as sensors. The Flex-Stak fuel cell is an excellent learning tool that gives hands-on experience with promising fuel cell technology. Whether it’s advanced research on MEAs, creating your own fuel cell lab or conducting professional training the Flex-Stak has a load of practical applications.
The Flex-Stak Assembled is a fully assembled, tested, and ready for use PEM Fuel Cell! Only a flathead screwdriver and torque wrench (<50 in-lb, 1/4 inch nut) are necessary to assemble the Flex-Stak so you can concentrate on creating your very own hydrogen powered applications.
The Flex-Stak design is a dismantable fuel cell that allows for the user to input their own custom PEM MEAs for testing!
✔ Plastic Endplates
✔ Graphite Composite Bipolar/Monopolar Plates
✔ High Performance PEM MEAs
✔ Expandable Design (See Flex-Stak Expansion Kits)
✔ Guide Dowels
✔ Dis-assembly and Reassembly Instructions
Please note that the kits do not come with the plastic case seen in the picture.
• MEA Active Area: 3.2 x 3.2cm (10cm²)
• MEA Membrane Area: 5.3 x 5.3cm
• Graphite Plate Overall Dimensions (L x W x D): 6.3 x 6.3 x 0.4 cm
• Recommended Torque Value: 8-10 inlbs
|Flex-Stak Properties||1 Cell||5 Cell||10 Cell||15 Cell||20 Cell|
|Nominal Output - Watts*||0.25 to 0.35||3 to 3.5||6 to 7||9 to 11.5||12 to 14|
|Nominal Operating Voltage**||0.45 to 0.6||2.3 to 3||4.6 to 6||7 to 9||9.5 to 12|
|Hydrogen Consumption (cc/minute)||10.6||53||106||162||400|
* The provided power output numbers are based on the forced air operation using the fan.
** The Flex-Stak nominal operating voltage per cell is typically around 0.45 to 0.6 V, but could vary between 0.4 and 0.9V per cell depending on how hard you are running the cell (i.e. pulling more current will result in a lower cell voltage, less current will have a higher cell voltage). Humidity of the H2 gas and stack temperature will also play a major role in the power output (or voltage or current) values.
Write a review
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: