- Fuel Cell Cars
- Education
- Fuel Cell Stacks
-
Fuel Cell Testing
- - Fixed Testing Systems
- - Liquid and Gas Delivery Systems
- - Fuel Cell Testing Hardware
- - Modular Testing Systems
- - Vacuum Tables and Temperature Controllers
- - Electronic Measurement and Control
- - Stack Humidification Systems
- - Ion Exchange Filters
- - Fuel Cell Testing Components
- - Portable Generators
- - Electrochemical Experiments
- Fuel Cell Components
- Hydrogen Equipment
- Hydrogen Drone
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- Clearance
- STEM Education
Fumapem F-930-RFS
Fumapem F-930-RFS membrane is a perflourinated cation exchange membrane with low resistance, high mechanical stability, low dimensional swelling, and high stability in acidic environments.
Fumapem F-930-RFS membrane comes in either a 10cm x 10cm or 20cm x 30cm size sheet.
Fumatech membranes are highly sensitive to differences in humidity and moisture content. Therefore the membranes can vary +/- 0.5cm from the original cut sizes. Also due to this sensitivity the manufacturer expects wrinkles to form, however soaking the membranes in deionized water will return the membranes to the full size planar state according to the manufacturer.
• Applications: Designed for Fuel Cell Application (H2-PEMFC)
• Cation Exchange Membrane
• Thickness: 28 - 33 micrometers (1.11 - 1.29 mil)
• Sizes: 10cm x 10cm, 20cm x 30cm
Fumapem F-930-RFS Technical Specification Sheet
The membrane is the transparent foil, delivered on a backing layer (colorless rigid PET foil). Peel off carefully the membrane from the backing layer. The membrane is ready for use.
Keep membrane package closed / sealed when unused. Unpack membrane only for direct use and process immediately after opening. Store, handle and process the membrane in a clean and dust-free area. Use only new and sharp knives or blades, when cutting the membrane. Always wear protective gloves when handling the membrane. Handle with care, be sure not to puncture, crease or scratch the membrane, otherwise leaks will occur. All surfaces in contact with the membrane during handling, inspection, storage and mounting must be smooth and free of sharp projections.
The membrane does not need any pre-treatment and is ready for use. Please assemble the membrane in dry form. If you have any concerns about storage, chemical stability, and pre-treatment please feel free to contact us for further information.
The membrane can be stored dry for an unlimited amount of time. However, the membrane has to be conditioned (washed and rinsed) prior to use.
Please note that a current lead time of one to two weeks is to be expected.
Membrane Properties | |
Membrane | Cation Exchange Membrane |
Thickness | 28 - 33 µm (microns) |
Appearance / Color | Transparent / Colorless |
Backing Foil | PET Foil |
Delivery Form | Dry |
Reinforcement | Yes |
Tensile Strength - max. (MPa) | > 20 MPa |
Non-Std Modulus (MPa) | > 230 MPa |
Yield Strength at 23°C / 50 % R.H. | > 10 MPa |
Elongation to Break (%) | > 150 % |
Specific Area Resistance | < 0.15 (in H2O at 25°C in H-form) Ω•cm2 |
Specific Conductivity | 110 (in H2O at 25°C in H-form) mS•cm-1 |
Counter Ion | H-form |
Ion Exchange Capacity | 0.89 - 1.02 (in H2O at 25°C in H-form) meq•g-1 |
Uptake in H2O at 25°C | 15 (in H-form) wt % |
Dimensional Swelling in H2O at 25°C | 3 (in H-form) % |
Write a review
Your Name:
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: