- Fuel Cell Cars
- Fuel Cell Stacks
Fuel Cell Testing
- - Fixed Testing Systems
- - Liquid and Gas Delivery Systems
- - Fuel Cell Testing Hardware
- - Modular Testing Systems
- - Vacuum Tables and Temperature Controllers
- - Electronic Measurement and Control
- - Stack Humidification Systems
- - Ion Exchange Filters
- - Fuel Cell Testing Components
- - Portable Generators
- - Electrochemical Experiments
- Fuel Cell Components
- Hydrogen Equipment
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- STEM Education
Fumasep FAAM-10 is an anion-exchange membrane – non-reinforced – thickness 10 µm, with low resistance, high selectivity, and high stability in acidic and caustic environment. The polymer backbone for this membrane is based on a proprietary hydrocarbon resin.
Fumasep FAAM-10 membrane comes in either a 10cm x 10cm or 20cm x 30cm size sheet.
Fumatech membranes are highly sensitive to differences in humidity and moisture content. Therefore the membranes can vary +/- 0.5cm from the original cut sizes. Also due to this sensitivity the manufacturer expects wrinkles to form, however soaking the membranes in deionized water will return the membranes to the full size planar state according to the manufacturer.
• Applications: Alkaline electrolysis using liquid aqueous KOH (6 – 12 M KOH), preferentially at both, anode and cathode side.
• Anion Exchange Membrane
• Operation range: 6 – 12 M KOH, temperature RT – 100 °C.
• Thickness (dry): 10 – 13 micrometers (0.39 - 0.51 mil)
• Sizes: 10cm x 10cm, 20cm x 30cm
The membrane is the thin brown foil, delivered on a backing layer (colorless rigid PET foil). Carefully separate the membrane from the backing layers. The membrane is delivered in dry form.
Keep membrane package closed / sealed when unused. Unpack membrane only for direct use and process it immediately after opening. Store, handle and process the membrane in a clean and dustfree area. Use only new and sharp knives or blades, when cutting the membrane. Always wear protective gloves when handling the membrane. Handle with care, be sure not to puncture, crease or scratch the membrane, otherwise leaks will occur. All surfaces which may get into contact with the membrane during inspection, storage, pretreatment and mounting must be free of sharp edges or angles.
Dry form: Storage for long time scale (> 12 month) may be done in dry state (sealed container). Wet form: Storage for short and medium time scale (hours up to several weeks) may be done in unsealed containers in 0.5 – 1.5 wt% NaCl solution or comparable neutral pH electrolytes. For storage over a longer time period a sealed container is recommended using afore said electrolyte with additional sodium sulfite (Na2SO3) in concentration 1 – 3 wt% to avoid biological fouling.
No specific pretreatment required. The membrane is self-activating in the cell after contact with aqueous caustic electrolyte (e.g. 6 - 9 M aqueous KOH solution) within several hours.
Depending on cell design, activation may also be done before assembling: Put the membrane sample between stabilizing meshes (in order to avoid curling) in aqueous KOH solution (concentration according to application) for at least 24 hrs at room temperature. Use closed container to avoid CO2 contamination (carbonate formation that may affect conductivity). Membranes must be covered by KOH solution. Membranes will expand when subject to swelling process. The hydration level can be controlled by KOH concentration and temperature, e.g. 9 M KOH solution at room temperature leads to approx. 50 – 70 wt% hydration level.
If you have any concerns about storage, chemical stability, pre-treatment or before proceeding, please feel free to contact us for further information.
Please note that a current lead time of four to six weeks is to be expected.
|Membrane||Anion Exchange Membrane|
|Thickness||10 – 13 µm (microns)|
|Appearance / Color||Light Brown, transparent|
|Yield Strength at 23°C / 50 % R.H.||> 100 MPa|
|Elongation to Break (%)||> 30 %|
|Young’s modulus at 23 °C / 50 % r.h.||> 2000 MPa|
|pH durability range||Stable under highly alkaline conditions|
Write a review
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: