- Fuel Cell Cars
- Education
- Fuel Cell Stacks
-
Fuel Cell Testing
- - Fixed Testing Systems
- - Liquid and Gas Delivery Systems
- - Fuel Cell Testing Hardware
- - Modular Testing Systems
- - Vacuum Tables and Temperature Controllers
- - Electronic Measurement and Control
- - Stack Humidification Systems
- - Ion Exchange Filters
- - Fuel Cell Testing Components
- - Portable Generators
- - Electrochemical Experiments
- Fuel Cell Components
- Hydrogen Equipment
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- Clearance
- STEM Education
Fumasep FKD-PK-75
Fumasep FKD-PK-75 is a PK reinforced Cation Exchange Membrane (CEM) with low resistance, high selectivity, high mechanical stability, and high stability in caustic environment.
Fumasep FKD-PK-75 membrane comes in either a 10cm x 10cm or 20cm x 30cm size sheet. The membrane is the light brown foil delivered in wet form (2 wt% NaCl solution).
Fumatech membranes are highly sensitive to differences in humidity and moisture content. Therefore the membranes can vary +/- 0.5cm from the original cut sizes. Also due to this sensitivity the manufacturer expects wrinkles to form, however soaking the membranes in deionized water will return the membranes to the full size planar state according to the manufacturer.
• Applications: Diffusion dialysis for caustic solutions.
• Cation Exchange Membrane
• Stability range (pH) at 25 ºC: 1 - 14
• Thickness: 75 micrometers (2.91 mil)
• Size: 10cm x 10cm, 20cm x 30cm
Fumasep FKD-PK-75 Technical Specification Sheet
Keep membrane package closed / sealed when unused. Store, handle and process the membrane in a clean and dust-free area. Use only new and sharp knives or blades, when cutting the membrane. Always wear protective gloves when handling the membrane. Handle with care, be sure not to puncture, crease or scratch the membrane, otherwise leaks will occur. All surfaces in contact with the membrane during handling, inspection, storage and mounting must be smooth and free of sharp projections.
Storage for short and medium time scale (hours up to several weeks) may be done in unsealed containers in 0.5 - 2 wt% NaCl solution or comparable neutral pH electrolytes. For storage over a longer time period a sealed container is recommended using afore said electrolyte with biocide to avoid biological fouling.
If you have any concerns about storage, chemical stability and pretreatment before proceeding, please feel free to contact us for further information.
Please note that a current lead time of one to two weeks is to be expected.
Membrane Properties | |
Membrane | Cation Exchange Membrane |
Thickness | 70 - 80 µm (microns) |
Appearance / Color | Transparent / Brown |
Backing Foil | None |
Delivery Form | Wet (2 wt% NaCl solution) |
Reinforcement | PEEK (PK) |
Tensile Strength - max. (MPa) | > 50 MPa |
Density | 9 - 10 mg•cm-2 |
Non-Std Modulus (MPa) | 2000 - 2500 MPa |
Yield Strength at 23°C / 50 % R.H. | 30 - 40 MPa |
Elongation to Break (%) | > 15 % |
Specific Area Resistance | 1.5 - 2.0 (in Na+ form) Ω•cm2 |
Specific Conductivity | 4 - 5 (in Na+ form) mS•cm-1 |
Counter Ion | Sodium Form (Na+) |
Ion Exchange Capacity | 1.4 - 1.6 (in Na+ form) meq•g-1 |
Selectivity | 96 - 99 % |
Uptake in H2O at 25°C | 20 - 30 wt % |
Dimensional Swelling in H2O at 25°C | 0 - 1 % |
Hydroxyl Transfer Rate | 300 - 600 µmol•min-1•cm-2 |
Bubble Point Test in Water at 25°C | > 2.5 bar |
Residual Solvent / Additive Content | < 3 % |
Write a review
Your Name:
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: