Your shopping cart is empty!
+1 (855) 251-0016 | email@example.com
- Fuel Cell Cars
- Fuel Cell Stacks
Fuel Cell Testing
- - Fixed Testing Systems
- - Liquid and Gas Delivery Systems
- - Fuel Cell Testing Hardware
- - Modular Testing Systems
- - Vacuum Tables and Temperature Controllers
- - Electronic Measurement and Control
- - Stack Humidification Systems
- - Ion Exchange Filters
- - Fuel Cell Testing Components
- - Portable Generators
- - Electrochemical Experiments
- Fuel Cell Components
- Hydrogen Equipment
- Power Devices
- Solar Power
- Hydro Power
- Wind Power
- Bioenergy Power
- Lab Accessories
- STEM Education
DRIERITE (8 mesh) desiccants are made from the naturally occurring mineral, gypsum (Calcium Sulfate), and are available in several varieties designed to solve all types of drying problems. DRIERITE is an all purpose drying agent for the efficient and rapid drying of air, industrial gases, refrigerants, organic liquids and solids. It is used to maintain a dry atmosphere in storage spaces, vaults, commercial packages, and other enclosures; and for the protection of hygroscopic materials or materials subject to mildew, corrosion, rust, or other deterioration caused by high humidity.
The bulk density and tapped density of Drierite is the same at 65 pounds/cubic foot.
Forms of Drierite
The granular forms of DRIERITE are available in sizes ranging from powder to 4 mesh ( 1 /4 inch granules) weighing approximately 65 pounds per cubic foot, (60 pounds per cubic foot for 200 mesh powder). The powder is very well suited for removing the last traces of moisture from organic liquids and as an additive in polymer formulations. The most popular granule sizes are 200 mesh, 20-40 mesh, 10-20 mesh, 8 mesh, 6 mesh, and 4 mesh granules ("Mesh" means the number of granules per inch).
The moisture remaining in gases dried with DRIERITE at 25°C - 30°C is 0.005 mg/liter (data verified by the National Bureau of Standards). Air is dried to a dew point of -100°F. Organic liquids are dried to the low ppm range. There is little change in efficiency at temperatures up to 100°C.
Drierite DESICCANTS Capacity
For the drying of liquids, DRIERITE instantly absorbs 6.6 weight percent water by chemical action, creating the hemihydrate of calcium sulfate. For the drying of gases, DRIERITE has a water capacity of 10 to 14 weight percent. This increased capacity is due to combined chemical and capillary action. DRIERITE granules have 38% pore space volume, which accounts for the additional capacity. Above 6.6%, the capacity varies inversely with temperature and directly with pressure and the partial pressure of water vapor.
All forms of DRIERITE can be regenerated many times for reuse. See Regeneration of Drierite Desiccants below for details
Regeneration Of DRIERITE DESICCANTS
After normal use, any of the forms of DRIERITE may be regenerated for reuse. The operation is simple and involves only standard equipment. The used and exhausted desiccant should be ventilated to remove vapors, if any, and stored in a convenient container until a sufficient amount is accumulated to justify the work of regeneration.
Regular and Indicating DRIERITE
For the regeneration of Indicating DRIERITE and small lots of Regular DRIERITE , the granules may be spread in layers one granule deep and heated for 1 hour at 210°C or 425°F. The regenerated material should be placed in the the original glass or metal container and sealed while hot. The color of the Indicating DRIERITE may become less distinct on successive regeneration due to the migration of the indicator into the interior of the granule and sublimation of the indicator.
Commercial Grade and Du-Cal DRIERITE
Exhausted Commercial DRIERITE or Du-Cal DRIERITE should be spread about 1 inch deep in shallow pans and heated in a oven at 450°F or 230°C for 2 hours to achieve complete dehydration. The regenerated material should be placed in the original container and sealed while hot.
The Importance of Temperature
The temperature at which DRIERITE desiccants are regenerated is crucial in restoring DRIERITE to its original condition. Absorbed moisture is water of hydration and is chemically bound to the calcium sulfate of DRIERITE. Temperatures in the range of 400°F - 450°F are required to break these bonds and release absorbed moisture. Lower temperatures, regardless of heating time, will not regenerate DRIERITE unless applied under vacuum (26" Hg, 325°F or 28" Hg, 275°F). Care should be taken not to overheat DRIERITE Desiccants. High temperatures can alter the crystal structure and render the desiccants permanently inactive.
Write a review
Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: