• Titan EZ-240 Stack

Titan series PEM Electrolyzer Stacks is an advanced patented product, which is lower voltage and higher efficiency, energy-saving and of environmental protection, producing hydrogen and oxygen through the electrolysis of pure water (without adding alkali).

The proton exchange membrane (PEM), which only allows water and positive ions to cross between compartments. The membrane also serves as the electrolyte in the cell, eliminating the need for hazardous liquid electrolytes such as concentrated potassium hydroxide. PEM water electrolysis simply splits pure deionized water (H2O) into its constituent parts, hydrogen (H2) and oxygen (O2), on either side of this membrane. When a DC voltage is applied to the electrolyzer, water fed to the anode, or oxygen electrode, are oxidized to oxygen and protons, while electrons are released. The protons (H+ ions) pass through the PEM to the cathode, or hydrogen electrode, where they meet electrons from the other side of the circuit, and are reduced to hydrogen gas. The two reactions that occur in the cell are as follows:

1. 2H2O -> 4H+ + 4e- +O2
2. 4H+ + 4e- -> 2H2

Thus, the only possible components of the streams are hydrogen, oxygen and water moisture, as shown in Figure 1 below.

Application:

• Redundant renewable energy transformation and storage
• Lab experiment and teaching
• Laboratory analytic instrument
• Hydrogen healthy care industrial
• Hydrogen beauty industrial
• Fuel for special field
• Hydrogen supply for fuel cell
• Other pure H2 application field

Product Advantages:

• Produce hydrogen by electrolysis pure water (forbid adding alkaline)
• No corrosion or pollution
• High hydrogen purity
• Low electrolyzer cell resistance
• No heat and long desiccant replacement cycle
• Lower power consumption and high electrolysis efficiency

Technical Specifications:

Model Unit Titan EZ-60 Titan EZ-120 Titan EZ-180 Titan EZ-240 Titan EZ-300 Titan EZ-500 Titan EZ-800 Titan EZ-1000 Titan EZ-1300 Titan EZ-1500 Titan EZ-2000
Cells - 1 2 3 4 1 2 3 4 5 6 4
Stack Diameter mm 85 85 85 85 138 138 138 138 138 138 140
Active Area Diameter mm 40 40 40 40 80 80 80 80 80 80 94
H2 Flow Rate mL / min 0 - 60 0 - 120 0 - 180 0 - 240 0 - 300 0 - 500 0 - 800 0 - 1000 0 - 1300 0 - 1500 0 - 2000
O2 Flow Rate mL /min 0 - 30 0 - 60 0 - 90 0 - 120 0 - 150 0 - 250 0 - 400 0 - 500 0 - 650 0 - 750 0 - 1000
Voltage V (DC) 2 4 6 8 2 4 6 8 10 12 8
Max Input Current A (DC) 9 9 9 9 40 40 40 40 40 40 72
Water Consumption Rate cc / hr 4 8 12 16 18 30 48 60 78 90 120
Operating Temperature - 40°F to 113°F (5°C to 45°C)
Output Pressure - 0 - 10 barg (0 - 145 psi)
Membrane Type - Nafion PFSA
Sintered Titanium diffusion medium
Precious metal electrode
Need deionized or re-distilled water
Water Resistivity: >1 MΩ*cm
Water Conductivity: <1 us/cm
Estimated Lifetime: If the water quality and power supply are always in ideal condition you can expect about 10,000 hours of operation.

General lead time of two weeks to be expected.

Titan EZ-240 Stack is formerly known as QLC-240 PEM Electrolyzer Stack.

Titan EZ-240 Stack Manual

Titan Series Technical Data Sheet

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

Titan EZ-240 Stack

  • SKU: 60130004
  • $1,379.00


Related Products

Electrolyzer Hardware - Square
Interchangeable Test Hardware
Titan EZ-60 Stack
Titan EZ-120 Stack
Titan EZ-180 Stack

Titan EZ-180 Stack

$1,229.00

Titan EZ-300 Stack

Titan EZ-300 Stack

$1,636.00

Titan EZ-500 Stack

Titan EZ-500 Stack

$2,178.00

Titan EZ-1000 Stack
Titan EZ-2000 Stack
Titan EZ-800 Stack

Titan EZ-800 Stack

$2,909.00

Titan EZ-1300 Stack
Titan EZ-1500 Stack